|
Add:
|
EXHAUST NUT WRENCH - ALL AIRHEADS
Model:
Price: $34.00
Weight: 0.8lbs
Date Added: Monday 05 April, 2010
|
|
For exhaust systems with the finned aluminum nut holding the pipe onto the head. It is about 2 x 4.75” (50 x 120mm), compact enough to be carried ... more info |
|
Add:
|
MOLD-A-GAUGE
Model:
Price: $7.00
Weight: 0.1lbs
Date Added: Friday 02 April, 2010
|
|
Non-stick, non-shrink, heat cured material, used to measure the end play of the input, intermediate, and output shafts on the /2 /5 /6 /7 R26 R27 and ... more info |
|
Add:
|
CLUTCH INSTALLATION/REMOVAL BOLTS
Model:
Price: $8.00
Weight: 0.3lbs
Date Added: Friday 02 April, 2010
|
|
Three fine-thread bolts, nuts and hardened washers used to compress the diaphragm spring so you can remove and install the clutch components. They're ... more info |
|
Add:
|
CLUTCH INSTALLATION/REMOVAL BOLTS
Model:
Price: $8.00
Weight: 0.3lbs
Date Added: Friday 02 April, 2010
|
|
Three fine-thread bolts, nuts and hardened washers used to compress the diaphragm spring so you can remove and install the clutch components. These ... more info |
|
Add:
|
CLUTCH ALIGNMENT TOOL - 1951 to 1995 AIRHEADS
Model:
Price: $28.00
Weight: 0.4lbs
Date Added: Friday 02 April, 2010
|
|
This is the same alignment tool included in the clutch tool set. It's available separately here for those who don't need/already have the ... more info |
|
Add:
|
HUB NUT REMOVER /6 and /7
Model:
Price: $48.00
Weight: 1lbs
Date Added: Thursday 11 March, 2010
|
|
Tool that will remove the hub nut from /6, /7, R100S & RS (not the R60/6 or R80/7) motorcycles. It's designed to work even when some bozo has gouged ... more info |
|
Add:
|
WHEEL TUBE /2 and /5
Model:
Price: $15.00
Weight: 0.6lbs
Date Added: Thursday 11 March, 2010
|
|
Tube to aid in removing the wheel bearings, and to pre-load them while checking for correct spacer length. Shown in picture #169 in my copy of the /2 ... more info |
|
Add:
|
DRIVESHAFT U-JOINT BOLT TORQUE WRENCH ADAPTOR
Model:
Price: $21.00
Weight: 0.15lbs
Date Added: Thursday 11 March, 2010
|
|
BMW specifies a torque figure for the twelve sided bolts that hold the drive shaft universal joint onto the output flange of the transmission, but a ... more info |
|
Add:
|
FINAL DRIVE PINION GEAR HOLDER
Model:
Price: $37.00
Weight: 0.4lbs
Date Added: Thursday 11 March, 2010
|
|
Used to keep the pinion gear from rotating while unscrewing the pinion nut. For 1955 to 1995 airheads. Made from case hardened cold rolled steel. ... more info |
|
Add:
|
FINAL DRIVE SLOTTED NUT TOOL - /5 & LATER AIRHEADS
Model:
Price: $39.00
Weight: 0.7lbs
Date Added: Thursday 11 March, 2010
|
|
For all airheads 1970-1995 except R100GS. Used to remove the nut with the four slots that holds the oil seal and the pinion gear in place in the ... more info |
|
